How Wireless Power Works

Most electric toothbrushes recharge through inductive coupling.
Photo courtesy Amazon.com

­ Unless you are particularly organized and good with tie wrap, you probably have a few dusty power cord tangles around your home. You may have even had to follow one particular cord through the seemingly impossible snarl to the outlet, hoping that the plug you pull will be the right one. This is one of the downfalls of electricity. While it can make people's lives easier, it can add a lot of clutter in the process.

For these reasons, scientists have tried to develop methods of wireless power transmission that could cut the clutter or lead to clean sources of electricity. While the idea may sound futuristic, it isn't particularly new. Nicola Tesla proposed theories of wireless power transmission in the late 1800s and early 1900s. One of his more spectacular displays involved remotely powering lights in the ground at his Colorado Springs experiment station.

Advertisement

Tesla's work was impressive, but it didn't immediately lead to widespread, practical methods for wireless power transmission. Since then, researchers have developed several techniques for moving electricity over long distances without wires. Some exist only as theories or prototypes, but others are already in use. If you have an electric toothbrush, for example, you probably take advantage of one method every day.

­The wireless transmission of energy is common in much of the world. Radio waves are energy, and people use them to send and receive cell phone, TV, radio and WiFi signals every day. The radio waves spread in all directions until they reach antennae that are tuned to the right frequency. A similar method for transferring electrical power would be both inefficient and dangerous.

For example, a toothbrush's daily exposure to water makes a traditional plug-in charger potentially dangerous. Ordinary electrical connections could also allow water to seep into the toothbrush, damaging its components. Because of this, most toothbrushes recharge through inductive coupling. See the next page to learn more about how inductive coupling works.

Advertisement

Inductive Coupling

An electric toothbrush's base and handle contain coils that allow the battery to recharge.

Inductive coupling uses magnetic fields that are a natural part of current's movement through­ wire. Any time electrical current moves through a wire, it creates a circular magnetic field around the wire. Bending the wire into a coil amplifies the magnetic field. The more loops the coil makes, the bigger the field will be.

If you place a second coil of wire in the magnetic field you've created, the field can induce a current in the wire. This is essentially how a transformer works, and it's how an electric toothbrush recharges. It takes three basic steps:

Advertisement

  1. Current from the wall outlet flows through a coil inside the charger, creating a magnetic field. In a transformer, this coil is called the primary winding.
  2. When you place your toothbrush in the charger, the magnetic field induces a current in another coil, or secondary winding, which connects to the battery.
  3. This current recharges the battery.

You can use the same principle to recharge several devices at once. For example, the Splashpower recharging mat and Edison Electric's Powerdesk both use coils to create a magnetic field. Electronic devices use corresponding built-in or plug-in receivers to recharge while resting on the mat. These receivers contain compatible coils and the circuitry necessary to deliver electricity to devices' batteries.

A Splashpower mat uses induction to recharge multiple devices simultaneously.
© Copyright Splashpower 2006

A newer theory uses a similar setup to transmit electricity over longer distances. We'll look at how it works in the next section.

Advertisement

Resonance and Wireless Power

A trumpet's size, shape and material composition determine its resonant frequency.
Photo courtesy Stock.exchng

Household devices produce relatively small magnetic fields. For this reason, chargers hold devices at the distance necessary to induce a current, which can only happen if the coils are close together. A larger, stronger field could induce current from farther away, but the process would be extremely inefficient. Since a magnetic field spreads in all directions, making a larger one would waste a lot of energy.

In November 2006, however, researchers at MIT reported that they had discovered an efficient way to transfer power between coils separated by a few meters. The team, led by Marin Soljacic, theorized that they could extend the distance between the coils by adding resonance to the equation.

Advertisement

­ A good way to understand resonance is to think of it in terms of sound. An object's physical structure -- like the size and shape of a trumpet -- determines the frequency at which it naturally vibrates. This is its resonant frequency. It's easy to get objects to vibrate at their resonant frequency and difficult to get them to vibrate at other frequencies. This is why playing a trumpet can cause a nearby trumpet to begin to vibrate. Both trumpets have the same resonant frequency.

Research at MIT indicates that induction can take place a little differently if the electromagnetic fields around the coils resonate at the same frequency. The theory uses a curved coil of wire as an inductor. A capacitance plate, which can hold a charge, attaches to each end of the coil. As electricity travels through this coil, the coil begins to resonate. Its resonant frequency is a product of the inductance of the coil and the capacitance of the plates.

The MIT wireless power project uses a curved coil and capacitive plates.

As with an electric toothbrush, this system relies on two coils. Electricity, traveling along an electromagnetic wave, can tunnel from one coil to the other as long as they both have the same resonant frequency. The effect is similar to the way one vibrating trumpet can cause another to vibrate.

As long as both coils are out of range of one another, nothing will happen, since the fields around the coils aren't strong enough to affect much around them. Similarly, if the two coils resonate at different frequencies, nothing will happen. But if two resonating coils with the same frequency get within a few meters of each other, streams of energy move from the transmitting coil to the receiving coil. According to the theory, one coil can even send electricity to several receiving coils, as long as they all resonate at the same frequency. The researchers have named this non-radiative energy transfer since it involves stationary fields around the coils rather than fields that spread in all directions.

According to the theory, one coil can recharge any device that is in range, as long as the coils have the same resonant frequency.

The MIT team's preliminary work suggests that this kind of setup could power or recharge all the devices in one room. Some modifications would be necessary to send power over long distances, like the length of a building or a city. The team is making progress -- in June 2007, the MIT team published a paper detailing a successful demonstration of their prototype. They used resonating coils to power a light bulb over a distance of about seven feet (two meters) [Source: PhysOrg].

Other wireless power theories involve enormous distances -- like from space to the Earth. We'll look at those next.

Advertisement

Long-distance Wireless Power

The Stationary High Altitude Relay Platform (SHARP) unmanned plane could run off power beamed from the Earth.

Whether or not it incorporates resonance, induction generally sends power over relatively short distances. But some plans for wireless power involve moving electricity over a span of miles. A few proposals even involve sending power to the Earth from space.

In the 1980s, Canada's Communications Research Centre created a small airplane that could run off power beamed from the Earth. The unmanned plane, called the Stationary High Altitude Relay Platform (SHARP), was designed as a communications relay. Rather flying from point to point, the SHARP could fly in circles two kilometers in diameter at an altitude of about 13 miles (21 kilometers). Most importantly, the aircraft could fly for months at a time.

Advertisement

The secret to the SHARP's long flight time was a large, ground-based microwave transmitter. The SHARP's circular flight path kept it in range of this transmitter. A large, disc-shaped rectifying antenna, or rectenna, just behind the plane's wings changed the microwave energy from the transmitter into direct-current (DC) electricity. Because of the microwaves' interaction with the rectenna, the SHARP had a constant power supply as long as it was in range of a functioning microwave array.­

­ Rectifying antennae are central to many wireless power transmission theories. They are usually made an array of dipole antennae, which have positive and negative poles. These antennae connect to semiconductor diodes. Here's what happens:

  1. Microwaves, which are part of the electromagnetic spectrum, reach the dipole antennae.
  2. The antennae collect the microwave energy and transmit it to the diodes.
  3. The diodes act like switches that are open or closed as well as turnstiles that let electrons flow in only one direction. They direct the electrons to the rectenna's circuitry.
  4. The circuitry routes the electrons to the parts and systems that need them.

Other, longer-range power transmission ideas also rely on rectennae. David Criswell of the University of Houston has proposed the use of microwaves to transmit electricity to Earth from solar power stations on the moon. Tens of thousands of receivers on Earth would capture this energy, and rectennae would convert it to electricity.

Stations on Earth can receive energy from the moon via microwaves.

Microwaves pass through the atmosphere easily, and rectennae rectify microwaves into electricity very efficiently. In addition, Earth-based rectennae could be constructed with a mesh-like framework, allowing the sun and rain to reach the ground underneath and minimizing the environmental impact. Such a setup could provide a clean source of power. However, it does have some drawbacks:

  • The solar power stations on the moon would require supervision and maintenance. In other words, the project would require sustainable, manned moon bases.
  • Only part of the earth has a direct line of sight to the moon at any given time. To make sure the whole planet had a steady power supply, a network of satellites would have to re-direct the microwave energy.
  • Many people would resist the idea of being constantly bathed in microwaves from space, even if the risk were relatively low.

­ While scientists have built working prototypes of aircraft that run on wireless power, larger-scale applications, like power stations on the moon, are still theoretical. As the Earth's population continues to grow, however, the demand for electricity could outpace the ability to produce it and move it around. Eventually, wireless power may become a necessity rather than just an interesting idea.

Read on for lots more information about electricity, wireless power and related topics.

Advertisement

Lots More Information

Related HowStuffWorks Articles
More Great Links

Sources

  • American Microsemiconductor. "Diode - Rectifier." http://www.americanmicrosemi.com/tutorials/diode.htm
  • Biever, Celeste. "'Evanescent Coupling' Could Power Gadgets Wirelessly." 11/15/2006. http://www.newscientisttech.com/channel/tech/dn10575-evanescent-coupling-could-power-gadgets-wirelessly.html
  • Castelvecchi, Davide. "Wireless Energy Could Power Consumer, Industrial Electronics.' 11/14/2006. http://web.mit.edu/newsoffice/2006/wireless.html
  • Criswell, David R. "Lunar Solar Power System for Energy Prosperity within the 21st Century." http://www.worldenergy.org/wec-geis/publications/default/tech_papers/17th_congress/4_1_33.asp
  • Fildes, Jonathan. "Physics Promises Wireless Power." BBC. 11/15/2006. http://news.bbc.co.uk/2/hi/technology/6129460.stm
  • Gilbertson, Roger G. "Riding a Beam of Light: NASA's First Space Elevator Competition Proves Highly Challenging. Space.com. 10/24/2005. http://www.space.com/businesstechnology/051024_spaceelevator_challenge.html
  • Grebb, Michael. "Space Geeks Seek Wireless Power." Wired. 10/20/2005. http://www.wired.com/news/technology/technology/wireless_special/0,69038-0.html
  • Hermida, Alfred. "Wireless Power Charges Gadgets." 3/21/2003. http://news.bbc.co.uk/2/hi/technology/2861987.stm
  • Jull, George. "SHARP." Friends of CRC. 6/25/1996. http://www.friendsofcrc.ca/Projects/SHARP/sharp.html
  • Karalis, Aristeidis et al. "Wireless Non-Radiative Energy Transfer." http://arxiv.org/ftp/physics/papers/0611/0611063.pdf
  • Minkel, J.R. "Wireless Energy Transfer May Power Devices At a Distance." Scientific American. 11/14/2006. http://www.sciam.com/article.cfm?articleID=E87D47E5-E7F2-99DF-3AE75A880501B215
  • NASA. "Beam it Down, Scotty!" http://science.nasa.gov/headlines/y2001/ast23mar_1.htm
  • NASA. Beamed Laser Power for UAVs. http://www.nasa.gov/centers/dryden/news/FactSheets/FS-087-DFRC.html
  • NASA. Glenn Involvement with Laser Power Beaming - Overview. http://powerweb.grc.nasa.gov/pvsee/programs/pvlaser_overview.html
  • Tesla, Nicola. "The Transmission of Electric Energy Without Wires." Electric World and Engineer. 1904. Reprinted at PBS. http://www.pbs.org/tesla/res/res_art08.html
  • Tesla, Nicola. "The True Wireless." The Electrical Experimenter, May 1919. Reprinted at PBS. http://www.pbs.org/tesla/res/res_art06.html
  • The Economist. "Cut the Cables." 11/16/2006 http://www.economist.com/science/displayStory.cfm?story_id=8167009

Advertisement

Loading...